Not sure if I am doing something wrong ot just the library does not work on Arduino Nano 33 BLE.This library allows to control the Wiring I/O board from Processing without writing code in the Wiring IDE. This report would have more information with In file included from C:\Users\GEORGE\Documents\Arduino\libraries\Tic/Tic.h:15:0,įrom C:\Users\GEORGE\Documents\Arduino\libraries\Tic\Tic.cpp:1:Ĭ:\Users\GEORGE\AppData\Local\Arduino15\packages\arduino\hardware\mbed_nano\2.2.0\libraries\Wire/Wire.h:59:20: note: candidate: virtual size_t arduino::MbedI2C::write(uint8_t)Ĭ:\Users\GEORGE\AppData\Local\Arduino15\packages\arduino\hardware\mbed_nano\2.2.0\libraries\Wire/Wire.h:60:20: note: candidate: virtual size_t arduino::MbedI2C::write(int)Ĭ:\Users\GEORGE\Documents\Arduino\libraries\Tic\Tic.cpp:191:22: error: call of overloaded 'write(uint32_t)' is ambiguousĬ:\Users\GEORGE\Documents\Arduino\libraries\Tic\Tic.cpp:192:23: error: call of overloaded 'write(uint32_t)' is ambiguousĬ:\Users\GEORGE\Documents\Arduino\libraries\Tic\Tic.cpp:193:23: error: call of overloaded 'write(uint32_t)' is ambiguousĮrror compiling for board Arduino Nano 33 BLE.
In file included from C:\Users\GEORGE\Documents\Arduino\libraries\Tic\Tic.cpp:1:0:Ĭ:\Users\GEORGE\Documents\Arduino\libraries\Tic\Tic.cpp: In member function 'virtual void TicI2C::commandW32(TicCommand, uint32_t)':Ĭ:\Users\GEORGE\Documents\Arduino\libraries\Tic\Tic.cpp:190:22: error: call of overloaded 'write(uint32_t)' is ambiguous In file included from C:\Users\GEORGE\Documents\Arduino\sketch_jun20a\sketch_jun20a.ino:17:0:Ĭ:\Users\GEORGE\Documents\Arduino\libraries\Tic/Tic.h: In member function 'void TicBase::setAgcBottomCurrentLimit(TicAgcBottomCurrentLimit)':Ĭ:\Users\GEORGE\Documents\Arduino\libraries\Tic/Tic.h:688:63: warning: suggest parentheses around arithmetic in operand of '|' ĬommandW7(TicCommand::SetAgcOption, 0x10 | (uint8_t)limit & 0xF) Ĭ:\Users\GEORGE\Documents\Arduino\libraries\Tic/Tic.h: In member function 'void TicBase::setAgcCurrentBoostSteps(TicAgcCurrentBoostSteps)':Ĭ:\Users\GEORGE\Documents\Arduino\libraries\Tic/Tic.h:698:63: warning: suggest parentheses around arithmetic in operand of '|' ĬommandW7(TicCommand::SetAgcOption, 0x20 | (uint8_t)steps & 0xF) Ĭ:\Users\GEORGE\Documents\Arduino\libraries\Tic/Tic.h: In member function 'void TicBase::setAgcFrequencyLimit(TicAgcFrequencyLimit)':Ĭ:\Users\GEORGE\Documents\Arduino\libraries\Tic/Tic.h:708:63: warning: suggest parentheses around arithmetic in operand of '|' ĬommandW7(TicCommand::SetAgcOption, 0x30 | (uint8_t)limit & 0xF)
This are the error messages Arduino: 1.8.15 (Windows 10), Board: "Arduino Nano 33 BLE" I have upgraded to new Arduino Nano 33 BLE. I was using Tic 500 Stepper motor controller with my older Arduino Nano and it was working just fine.
0 kommentar(er)
